Versiones comparadas

Versión Versión anterior 1 Nueva versión 2
Cambios realizados por

Marina Herrera Martinez

Marina Herrera Martinez

Guardado el

Clave

  • Se ha añadido esta línea.
  • Se ha eliminado esta línea.
  • El formato se ha cambiado.


Advertencia
titleMandatory action

The activation of BC_SETs is mandatory along with the process of installing the version using the software component. Without this activation some product features may not work

...

To set up this table, go to transaction SM30→Refresh→ New entries.

In this table, you must make entries for the following tables:

  • EDOCOUNTRYTCH
  • EDOFILETYPE
  • EDOFILETYPEV
  • EDOFILETYPET
  • EDOSRCTYPE
  • EDOSRCTYPET
  • TBE31
  • TMENU01
  • TTREES
  • TVIMF
  • /EDGE/SII_PAR_MW
  • /EDGE/SII_CS001
  • /EDGE/SII_CS002
  • /EDGE/SII_MP_000
  • /EDGE/SII_MP_005
  • /EDGE/SII_PRIORI
  • /EDGE/SII_MPT014
  • /EDGE/SII_MP_014
  • /EDGE/SII_VAL_01
  • /EDGE/SII_CO_015
  • /EDGE/SII_MPT010
  • /EDGE/SII_MP_010


The order to activate these two BC_SETs is as follows:

...

This is due to the SAP version of this table. In product, the records in this table are marked by the key fields:

  • PROCESS
  • VERSION
  • PROCESS_STEP

Image Added

However, in different versions the key fields may have a non-key field as the second field:

Image Added

This causes problems when entering BC_SET entries in this table.

If this is the case, and this error occurs in this BC_SET, proceed as follows.

Activate BC_SET despite the error so that all other tables in this BC_SET are recorded in the system.

Then, enter the following entries manually in the view of the SM30 EDOPROCSTEPVERV:

Image Added

Put these table entries into the transfer order (workbench) that BC_SET generates so that they are transported to all other environments.

Once the consistency has been checked, click on the icon Image Addedto activate it.

Press OK as many times as necessary. During activation, the process will request a transfer order.

This way BC_SET would be activated.

It may be that after activation is complete, a message appears with information about the activation:

Termination with warnings

Image Added

To view these warnings click on the log icon:

Image Added


The same warnings appear as when you performed the BC_SET consistency.

If the error occurred earlier in table EDOPROCSTEPV, you can display the error in the log.

Image Added

To check that it has been activated successfully, you must check that the following tables appear in the generated transfer order:

  • /EDGE/SII_MP_000
  • /EDGE/SII_MP_005
  • /EDGE/SII_MP_010
  • /EDGE/SII_PRIORI
  • BALOBJ
  • EDOPROCSTEPV
  • EDOTYPEV
  • /EDGE/SII_CS002 
  • EDOPROCSTEPVERV (if it did not work with BC_SET, enter the manually added entries in the transfer order)
  • V_BALSUB

Image Added

Repeat this process for BC_SET /EDGE/SII_BC_SET_SP5_CON_MANDANT in all available clients.

During the activation of this BC_SET, two transfer orders will be requested. One will be from Workbench and one from Cust. To check that it has been activated correctly, check that the following tables have been entered in the Workbench command:

  • /EDGE/SII_CO_015
  • TVIMF
  • V_TVIMF

Image Added

and in Custo's order:

Image Added

Info
iconfalse

This BC_SET must be activated in all clients, but the only orders required to transport to other environments are those that are created when you first activate BC_SET in a client. The Workbench order that is generated will have to be transported to the corresponding environments in a single client. On the other hand, the order you generate from Customizing must be transported to all other environments in all clients.

If, when you activate BC_SET in other development clients, transfer orders are generated, these orders can be ignored.